Move all to deprecated folder.

deprecated/firmware/buildroot/board/freescale/imx28evk/create-boot-sd.sh

@@ -0,0 +1,97 @@
+#!/bin/sh
+
+set -u
+set -e
+
+PROGNAME=$(basename $0)
+
+usage()
+{
+    echo "Create an SD card that boots on an i.MX28 EVK board."
+    echo
+    echo "Note: all data on the the card will be completely deleted!"
+    echo "Use with care!"
+    echo "Superuser permissions may be required to write to the device."
+    echo
+    echo "Usage: ${PROGNAME} <sd_block_device>"
+    echo "Arguments:"
+    echo "  <sd_block_device>     The device to be written to"
+    echo
+    echo "Example: ${PROGNAME} /dev/mmcblk0"
+    echo
+}
+
+if [ $# -ne 1 ]; then
+    usage
+    exit 1
+fi
+
+if [ $(id -u) -ne 0 ]; then
+    echo "${PROGNAME} must be run as root"
+    exit 1
+fi
+
+DEV=${1}
+
+# The partition name prefix depends on the device name:
+# - /dev/sde -> /dev/sde1
+# - /dev/mmcblk0 -> /dev/mmcblk0p1
+if echo ${DEV}|grep -q mmcblk ; then
+    PART="p"
+else
+    PART=""
+fi
+
+PART1=${DEV}${PART}1
+PART2=${DEV}${PART}2
+PART3=${DEV}${PART}3
+
+# Unmount the partitions if mounted
+umount ${PART1} || true
+umount ${PART2} || true
+umount ${PART3} || true
+
+# First, clear the card
+dd if=/dev/zero of=${DEV} bs=1M count=20
+
+sync
+
+# Partition the card.
+# SD layout for i.MX28 boot:
+# - Special partition type 53 at sector 2048, containing an SD-SB-encapsulated u-boot
+# - FAT partition containing zImage
+# - ext2/3 partition formatted as ext2 or ext3, containing the root filesystem.
+sfdisk --force -u S ${DEV} <<EOF
+2048,2000,53
+4048,16000,b
+20048,,L
+EOF
+
+sync
+
+# Copy the bootloader at offset 2048
+# (We need to skip the partition table in the .sd, too.)
+dd if=output/images/u-boot.sd of=${DEV}1 bs=1M
+
+# Prepare a temp dir for mounting partitions
+TMPDIR=$(mktemp -d)
+ 
+# FAT partition: kernel
+mkfs.vfat ${PART2}
+mount ${PART2} ${TMPDIR}
+cp output/images/*Image ${TMPDIR}/
+cp output/images/*.dtb  ${TMPDIR}/ || true
+sync
+umount ${TMPDIR}
+
+# ext2 partition: root filesystem
+mkfs.ext2 ${PART3}
+mount ${PART3} ${TMPDIR}
+tar -C ${TMPDIR}/ -xf output/images/rootfs.tar
+sync
+umount ${TMPDIR}
+
+# Cleanup
+rmdir ${TMPDIR}
+sync
+echo Done

deprecated/firmware/buildroot/board/freescale/imx28evk/readme.txt

@@ -0,0 +1,58 @@
+**************************
+Freescale i.MX28 EVK board
+**************************
+
+This file documents the Buildroot support for the Freescale i.MX28 EVK board.
+
+Read the i.MX28 Evaluation Kit Quick Start Guide [1] for an introduction to the
+board.
+
+Build
+=====
+
+First, configure Buildroot for your i.MX28 EVK board:
+
+  make freescale_imx28evk_defconfig
+
+Build all components:
+
+  make
+
+You will find in ./output/images/ the following files:
+  - imx28-evk.dtb
+  - rootfs.tar
+  - u-boot.sd
+  - zImage
+
+Create a bootable SD card
+=========================
+
+To determine the device associated to the SD card have a look in the
+/proc/partitions file:
+
+  cat /proc/partitions
+
+Run the following script as root on your SD card. This will partition the card
+and copy the bootloader, kernel and root filesystem as needed.
+
+*** WARNING! The script will destroy all the card content. Use with care! ***
+
+  ./board/freescale/imx28evk/create-boot-sd.sh <your-sd-device>
+
+Boot the i.MX28 EVK board
+=========================
+
+To boot your newly created system (refer to the i.MX28 EVK Quick Start Guide
+[1] for guidance):
+- insert the SD card in the SD Card Socket 0 of the board;
+- verify that your i.MX28 EVK board jumpers and switches are set as mentioned
+  in the i.MX28 EVK Quick Start Guide [1];
+- connect an RS232 UART cable to the Debug UART Port and connect using a
+  terminal emulator at 115200 bps, 8n1;
+- power on the board.
+
+Enjoy!
+
+References
+==========
+[1] http://cache.freescale.com/files/32bit/doc/user_guide/EVK_imx28_QuickStart.pdf