Move all to deprecated folder.

deprecated/firmware/buildroot/board/freescale/mpc8315erdb/linux-4.2.config

@@ -0,0 +1,70 @@
+CONFIG_FSL_EMB_PERFMON=y
+CONFIG_SYSVIPC=y
+CONFIG_POSIX_MQUEUE=y
+CONFIG_HIGH_RES_TIMERS=y
+CONFIG_IKCONFIG=y
+CONFIG_IKCONFIG_PROC=y
+CONFIG_SYSCTL_SYSCALL=y
+CONFIG_EMBEDDED=y
+CONFIG_MODULES=y
+# CONFIG_PPC_CHRP is not set
+# CONFIG_PPC_PMAC is not set
+CONFIG_PPC_83xx=y
+CONFIG_MPC831x_RDB=y
+CONFIG_MCU_MPC8349EMITX=y
+CONFIG_PCI=y
+CONFIG_PCIEPORTBUS=y
+# CONFIG_PCIEASPM is not set
+CONFIG_NET=y
+CONFIG_PACKET=y
+CONFIG_UNIX=y
+CONFIG_INET=y
+CONFIG_DEVTMPFS=y
+CONFIG_DEVTMPFS_MOUNT=y
+CONFIG_MTD=y
+CONFIG_MTD_CMDLINE_PARTS=y
+CONFIG_MTD_BLOCK=y
+CONFIG_MTD_CFI=y
+CONFIG_MTD_CFI_AMDSTD=y
+CONFIG_MTD_PHYSMAP_OF=y
+CONFIG_MTD_NAND=y
+CONFIG_MTD_NAND_FSL_ELBC=y
+CONFIG_SCSI_MQ_DEFAULT=y
+CONFIG_BLK_DEV_SD=y
+CONFIG_SCSI_CONSTANTS=y
+CONFIG_ATA=y
+CONFIG_SATA_FSL=y
+CONFIG_NETDEVICES=y
+CONFIG_GIANFAR=y
+CONFIG_REALTEK_PHY=y
+CONFIG_SERIAL_8250=y
+CONFIG_SERIAL_8250_CONSOLE=y
+CONFIG_I2C=y
+CONFIG_I2C_CHARDEV=y
+CONFIG_I2C_MPC=y
+CONFIG_SPI=y
+CONFIG_SPI_FSL_SPI=y
+CONFIG_GPIO_SYSFS=y
+CONFIG_GPIO_MPC8XXX=y
+CONFIG_WATCHDOG=y
+CONFIG_8xxx_WDT=y
+CONFIG_USB=y
+CONFIG_USB_EHCI_HCD=y
+CONFIG_USB_EHCI_FSL=y
+CONFIG_USB_STORAGE=y
+CONFIG_RTC_CLASS=y
+CONFIG_RTC_DRV_DS1307=y
+CONFIG_RTC_DRV_GENERIC=y
+CONFIG_DMADEVICES=y
+CONFIG_FSL_DMA=y
+CONFIG_ASYNC_TX_DMA=y
+CONFIG_EXT4_FS=y
+CONFIG_FANOTIFY=y
+CONFIG_VFAT_FS=y
+CONFIG_PROC_KCORE=y
+CONFIG_TMPFS=y
+CONFIG_JFFS2_FS=y
+CONFIG_SQUASHFS=y
+CONFIG_NLS_CODEPAGE_437=y
+CONFIG_NLS_ISO8859_1=y
+CONFIG_CRYPTO_DEV_TALITOS=y

deprecated/firmware/buildroot/board/freescale/mpc8315erdb/readme.txt

@@ -0,0 +1,62 @@
+
+******************** WARNING ********************
+The compiled U-Boot binary is intended for NAND flash only!
+It won't work for NOR and will brick that bootloader!
+
+Also don't go playing around with different U-boot versions or flash targets
+unless you've got the necessary hardware and/or know-how to unbrick your kit.
+
+2014.04 is known good for NAND.
+******************** WARNING ********************
+
+You'll need to program the files created by buildroot into the flash.
+The fast way is to tftp transfer the files via one of the network interfaces.
+
+Alternatively you can transfer the files via serial console with an Ymodem
+file transfer from your terminal program by using a "loady" command
+from the u-boot prompt instead of the "tftp ..." commands stated below.
+Beware that serial console file transfers are quite slow!
+
+Remember to set the MPC8315ERDB switches to NAND boot if you want to use
+your newly built U-Boot.
+
+1. Program the new U-Boot binary to NAND flash (optional)
+    If you don't feel confident upgrading your bootloader then don't do it,
+    it's unnecessary most of the time.
+
+    => tftp $loadaddr u-boot-nand.bin
+    => nand erase 0 0x80000
+    => nand write $loadaddr 0 0x80000 $filesize
+
+2. Program the kernel to NAND flash
+
+    => tftp $loadaddr uImage
+    => nand erase 0x100000 0x1e0000
+    => nand write $loadaddr 0x100000 0x1e0000
+
+3. Program the DTB to NAND flash
+
+    => tftp $loadaddr mpc8315erdb.dtb
+    => nand erase 0x2e0000 0x20000
+    => nand write $loadaddr 0x2e0000 0x20000
+
+4. Program the root filesystem to NAND flash
+
+    => tftp $loadaddr rootfs.jffs2
+    => nand erase 0x400000 0x1c00000
+    => nand write $loadaddr 0x400000 $filesize
+
+5. Booting your new system
+
+    => setenv nandboot 'setenv bootargs root=/dev/mtdblock3 rootfstype=jffs2 console=$consoledev,$baudrate;nand read $fdtaddr 0x2e0000 0x20000;nand read $loadaddr 0x100000 0x1e0000;bootm $loadaddr - $fdtaddr'
+
+    If you want to set this boot option as default:
+
+    => setenv bootcmd 'run nandboot'
+    => saveenv
+
+    ...or for a single boot:
+
+    => run nandboot
+
+    You can login with user "root".