Bump buildroot to version 2017-02

TG-3 #closed

bsp/buildroot/board/atmel/at91sam9260ek/linux-3.9.config

@@ -1,98 +0,0 @@
-CONFIG_EXPERIMENTAL=y
-# CONFIG_LOCALVERSION_AUTO is not set
-CONFIG_KERNEL_LZO=y
-# CONFIG_SWAP is not set
-CONFIG_SYSVIPC=y
-CONFIG_LOG_BUF_SHIFT=14
-CONFIG_BLK_DEV_INITRD=y
-CONFIG_SLAB=y
-CONFIG_MODULES=y
-CONFIG_MODULE_UNLOAD=y
-# CONFIG_BLK_DEV_BSG is not set
-# CONFIG_IOSCHED_DEADLINE is not set
-# CONFIG_IOSCHED_CFQ is not set
-CONFIG_ARCH_AT91=y
-CONFIG_ARCH_AT91SAM9260=y
-CONFIG_ARCH_AT91SAM9260_SAM9XE=y
-CONFIG_MACH_AT91SAM9260EK=y
-CONFIG_MACH_CAM60=y
-CONFIG_MACH_SAM9_L9260=y
-CONFIG_MACH_AFEB9260=y
-CONFIG_MACH_USB_A9260=y
-CONFIG_MACH_QIL_A9260=y
-CONFIG_MACH_CPU9260=y
-CONFIG_MACH_FLEXIBITY=y
-CONFIG_MACH_SNAPPER_9260=y
-CONFIG_MACH_AT91SAM_DT=y
-CONFIG_AT91_PROGRAMMABLE_CLOCKS=y
-# CONFIG_ARM_THUMB is not set
-CONFIG_ZBOOT_ROM_TEXT=0x0
-CONFIG_ZBOOT_ROM_BSS=0x0
-CONFIG_ARM_APPENDED_DTB=y
-CONFIG_ARM_ATAG_DTB_COMPAT=y
-CONFIG_CMDLINE="mem=64M console=ttyS0,115200 initrd=0x21100000,3145728 root=/dev/ram0 rw"
-CONFIG_FPE_NWFPE=y
-CONFIG_NET=y
-CONFIG_PACKET=y
-CONFIG_UNIX=y
-CONFIG_INET=y
-CONFIG_IP_PNP=y
-CONFIG_IP_PNP_BOOTP=y
-# CONFIG_INET_XFRM_MODE_TRANSPORT is not set
-# CONFIG_INET_XFRM_MODE_TUNNEL is not set
-# CONFIG_INET_XFRM_MODE_BEET is not set
-# CONFIG_INET_LRO is not set
-# CONFIG_IPV6 is not set
-CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
-CONFIG_MTD=y
-CONFIG_MTD_CMDLINE_PARTS=y
-CONFIG_MTD_NAND=y
-CONFIG_MTD_NAND_ATMEL=y
-CONFIG_MTD_UBI=y
-CONFIG_BLK_DEV_RAM=y
-CONFIG_BLK_DEV_RAM_SIZE=8192
-CONFIG_SCSI=y
-CONFIG_BLK_DEV_SD=y
-CONFIG_SCSI_MULTI_LUN=y
-CONFIG_NETDEVICES=y
-CONFIG_MII=y
-CONFIG_MACB=y
-# CONFIG_INPUT_MOUSEDEV_PSAUX is not set
-# CONFIG_INPUT_KEYBOARD is not set
-# CONFIG_INPUT_MOUSE is not set
-# CONFIG_SERIO is not set
-CONFIG_SERIAL_ATMEL=y
-CONFIG_SERIAL_ATMEL_CONSOLE=y
-# CONFIG_HW_RANDOM is not set
-CONFIG_I2C=y
-CONFIG_I2C_CHARDEV=y
-CONFIG_I2C_GPIO=y
-# CONFIG_HWMON is not set
-CONFIG_WATCHDOG=y
-CONFIG_WATCHDOG_NOWAYOUT=y
-CONFIG_AT91SAM9X_WATCHDOG=y
-# CONFIG_USB_HID is not set
-CONFIG_USB=y
-CONFIG_USB_DEVICEFS=y
-CONFIG_USB_MON=y
-CONFIG_USB_OHCI_HCD=y
-CONFIG_USB_STORAGE=y
-CONFIG_USB_STORAGE_DEBUG=y
-CONFIG_USB_GADGET=y
-CONFIG_USB_ZERO=m
-CONFIG_USB_GADGETFS=m
-CONFIG_USB_MASS_STORAGE=m
-CONFIG_USB_G_SERIAL=m
-CONFIG_RTC_CLASS=y
-CONFIG_RTC_DRV_AT91SAM9=y
-CONFIG_EXT2_FS=y
-CONFIG_VFAT_FS=y
-CONFIG_TMPFS=y
-CONFIG_UBIFS_FS=y
-CONFIG_CRAMFS=y
-CONFIG_NLS_CODEPAGE_437=y
-CONFIG_NLS_CODEPAGE_850=y
-CONFIG_NLS_ISO8859_1=y
-CONFIG_DEBUG_KERNEL=y
-CONFIG_DEBUG_USER=y
-CONFIG_DEBUG_LL=y

bsp/buildroot/board/atmel/readme.txt

@@ -13,7 +13,6 @@ This guide covers the following configurations:
  - atmel_sama5d3_xplained_dev_defconfig
  - atmel_sama5d3_xplained_mmc_defconfig
  - atmel_sama5d3_xplained_mmc_dev_defconfig
- - atmel_sama5d4ek_defconfig
  - atmel_sama5d4_xplained_defconfig
  - atmel_sama5d4_xplained_dev_defconfig
  - atmel_sama5d4_xplained_mmc_defconfig
@@ -45,7 +44,7 @@ using SAM-BA" section below.
 For the Xplained boards, an alternative Buildroot configuration is
 provided to boot from an SD card. Those configurations are labeled as
 'mmc'. In this case, after building Buildroot, follow the instructions
-in the "Preparting the SD card" sction.
+in the "Preparing the SD card" section.
 
 To configure and build Buildroot, run:
 

bsp/buildroot/board/atmel/sama5d2_xplained_mmc/genimage.cfg

@@ -23,6 +23,7 @@ image sdcard.img {
 		partition-type = 0xC
 		bootable = "true"
 		image = "boot.vfat"
+		offset = 1M
 	}
 
 	partition rootfs {

bsp/buildroot/board/atmel/sama5d3_xplained_mmc/genimage.cfg

@@ -23,6 +23,7 @@ image sdcard.img {
 		partition-type = 0xC
 		bootable = "true"
 		image = "boot.vfat"
+		offset = 1M
 	}
 
 	partition rootfs {

bsp/buildroot/board/atmel/sama5d4_xplained_mmc/genimage.cfg

@@ -24,6 +24,7 @@ image sdcard.img {
 		partition-type = 0xC
 		bootable = "true"
 		image = "boot.vfat"
+		offset = 1M
 	}
 
 	partition rootfs {