rpi/domo
1
0
Fork 0
Code Issues Pull Requests Releases Wiki Activity

Update buidlroot to version 2016.08.1

Browse Source
This commit is contained in:
NADAL Jean-Baptiste
2016-11-16 22:07:29 +01:00
parent 807ab03547
commit a1061efbc2
3636 changed files with 59539 additions and 25783 deletions
Download Patch File Download Diff File Expand all files Collapse all files

26
bsp/buildroot/board/freescale/warpboard/README
View File

@@ -9,7 +9,9 @@ Build all components:
You will find in ./output/images/ the following files:
- imx6sl-warp.dtb
- rootfs.ext4
- rootfs.tar
- sdcard.img
- u-boot.imx
- zImage
@@ -29,7 +31,7 @@ Update uboot
=> env default -f -a
=> saveenv
- Run the DFU toocommand in U-Boot:
- Run the DFU command in U-Boot:
=> dfu 0 mmc 0
- Transfer U-Boot into flash by running this command in host side:
@@ -42,14 +44,16 @@ Update uboot
Update linux & rootfs
=====================
Run the 'ums' command from the u6Boot prompt to mount the eMMC as mass
storage and update zImage, device tree (imx6sl-warp.dtb) and rootfs
file (rootfs.tar) :
Run the 'ums' command from the U-Boot prompt to mount the eMMC as USB mass
storage:
=> ums 0 mmc 0
Put the zImage and DTB files in the warp-vfat partition and extract as
root the rootfs.tar tarball in the warp-rootfs partition.
And then flash the sdcard.img into the eMMC:
dd if=output/images/sdcard.img of=/dev/<your-sd-device>
*** WARNING! This will destroy all the eMMC content. Use it with care! ***
Using bluetooth
================
@@ -62,4 +66,12 @@ $ hciconfig hci0 up
Using Wifi
==========
$ ifconfig wlan0 up
# modprobe brcmfmac
# iwconfig wlan0 essid ACCESSPOINTNAME
# wpa_passphrase ACCESSPOINTNAME > /etc/wpa.conf
(enter the wifi password and press enter)
# wpa_supplicant -Dwext -iwlan0 -c /etc/wpa.conf &
# udhcpc -i wlan0
# ping buildroot.org
Enjoy!

41
bsp/buildroot/board/freescale/warpboard/genimage.cfg Normal file
View File

@@ -0,0 +1,41 @@
# Minimal SD card image for the Warp board
#
# We mimic the .sdcard Freescale's image format for i.MX6SL:
# * the microSD card must have 1 kB free space at the beginning,
# * U-Boot is dumped as is,
# * a FAT partition at offset 8 MB is containing zImage and dtbs,
# * a single root filesystem partition is required (Ext4 in this case).
#
image boot.vfat {
vfat {
files = {
"imx6sl-warp.dtb",
"zImage"
}
}
size = 16M
}
image sdcard.img {
hdimage {
}
partition u-boot {
in-partition-table = "no"
image = "u-boot.imx"
offset = 1024
}
partition boot {
partition-type = 0xC
bootable = "true"
image = "boot.vfat"
offset = 8M
}
partition rootfs {
partition-type = 0x83
image = "rootfs.ext4"
}
}

1
bsp/buildroot/board/freescale/warpboard/linux.fragment Normal file
View File

@@ -0,0 +1 @@
CONFIG_CFG80211_WEXT=y

34
bsp/buildroot/board/freescale/warpboard/patches/linux/0001-hciuart-h4.patch
View File

@@ -1,34 +0,0 @@
From f6878a437a5ba157fd087ef5e1874bdce5eca199 Mon Sep 17 00:00:00 2001
From: Fabio Estevam <fabio.estevam@freescale.com>
Date: Mon, 22 Jun 2015 16:37:34 -0300
Subject: [PATCH] ARM: imx_v6_v7_defconfig: Select HCIUART_H4
The old warp board revision had hardware issues that prevented
the RTS/CTS lines to work with the Bluetooth module.
Tha latest rev1.12 fixes this problem, so now we should better use
CONFIG_BT_HCIUART_H4 instead, as it provides a better throughput than
the CONFIG_BT_HCIUART_3WIRE option.
Suggested-by: Arthur Lambert <arthur@dreem.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
---
arch/arm/configs/imx_v6_v7_defconfig | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/arch/arm/configs/imx_v6_v7_defconfig b/arch/arm/configs/imx_v6_v7_defconfig
index f6989fb..c864295 100644
--- a/arch/arm/configs/imx_v6_v7_defconfig
+++ b/arch/arm/configs/imx_v6_v7_defconfig
@@ -73,7 +73,7 @@ CONFIG_CAN=y
CONFIG_CAN_FLEXCAN=y
CONFIG_BT=y
CONFIG_BT_HCIUART=y
-CONFIG_BT_HCIUART_3WIRE=y
+CONFIG_BT_HCIUART_H4=y
CONFIG_CFG80211=y
CONFIG_CFG80211_WEXT=y
CONFIG_MAC80211=y
--
1.9.1

103
bsp/buildroot/board/freescale/warpboard/patches/linux/0002-replace-uart2-by-uart5.patch
View File

@@ -1,103 +0,0 @@
From: Fabio Estevam <fabio.estevam@freescale.com>
Date: Fri, 29 May 2015 16:19:39 -0300
Subject: [PATCH] ARM: dts: imx6sl-warp: Add changes for rev1.12
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
---
arch/arm/boot/dts/imx6sl-warp.dts | 32 +++++++++++++++++++-------------
1 file changed, 19 insertions(+), 13 deletions(-)
diff --git a/arch/arm/boot/dts/imx6sl-warp.dts b/arch/arm/boot/dts/imx6sl-warp.dts
index 0da906b..bdfa82b 100644
--- a/arch/arm/boot/dts/imx6sl-warp.dts
+++ b/arch/arm/boot/dts/imx6sl-warp.dts
@@ -61,7 +61,9 @@
usdhc3_pwrseq: usdhc3_pwrseq {
compatible = "mmc-pwrseq-simple";
reset-gpios = <&gpio4 5 GPIO_ACTIVE_LOW>, /* WL_REG_ON */
+ <&gpio4 7 GPIO_ACTIVE_LOW>, /* WL_HOSTWAKE */
<&gpio3 25 GPIO_ACTIVE_LOW>, /* BT_REG_ON */
+ <&gpio3 27 GPIO_ACTIVE_LOW>, /* BT_HOSTWAKE */
<&gpio4 4 GPIO_ACTIVE_LOW>, /* BT_WAKE */
<&gpio4 6 GPIO_ACTIVE_LOW>; /* BT_RST_N */
};
@@ -73,16 +75,16 @@
status = "okay";
};
-&uart2 {
+&uart3 {
pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_uart2>;
- fsl,uart-has-rtscts;
+ pinctrl-0 = <&pinctrl_uart3>;
status = "okay";
};
-&uart3 {
+&uart5 {
pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_uart3>;
+ pinctrl-0 = <&pinctrl_uart5>;
+ fsl,uart-has-rtscts;
status = "okay";
};
@@ -130,14 +132,6 @@
>;
};
- pinctrl_uart2: uart2grp {
- fsl,pins = <
- MX6SL_PAD_EPDC_D12__UART2_RX_DATA 0x41b0b1
- MX6SL_PAD_EPDC_D13__UART2_TX_DATA 0x41b0b1
- MX6SL_PAD_EPDC_D14__UART2_RTS_B 0x4130B1
- MX6SL_PAD_EPDC_D15__UART2_CTS_B 0x4130B1
- >;
- };
pinctrl_uart3: uart3grp {
fsl,pins = <
@@ -146,6 +140,15 @@
>;
};
+ pinctrl_uart5: uart5grp {
+ fsl,pins = <
+ MX6SL_PAD_ECSPI1_SCLK__UART5_RX_DATA 0x41b0b1
+ MX6SL_PAD_ECSPI1_MOSI__UART5_TX_DATA 0x41b0b1
+ MX6SL_PAD_ECSPI1_MISO__UART5_RTS_B 0x4130b1
+ MX6SL_PAD_ECSPI1_SS0__UART5_CTS_B 0x4130b1
+ >;
+ };
+
pinctrl_usdhc2: usdhc2grp {
fsl,pins = <
MX6SL_PAD_SD2_CMD__SD2_CMD 0x417059
@@ -158,6 +161,7 @@
MX6SL_PAD_SD2_DAT5__SD2_DATA5 0x417059
MX6SL_PAD_SD2_DAT6__SD2_DATA6 0x417059
MX6SL_PAD_SD2_DAT7__SD2_DATA7 0x417059
+ MX6SL_PAD_SD2_RST__SD2_RESET 0x417059
>;
};
@@ -173,6 +177,7 @@
MX6SL_PAD_SD2_DAT5__SD2_DATA5 0x4170b9
MX6SL_PAD_SD2_DAT6__SD2_DATA6 0x4170b9
MX6SL_PAD_SD2_DAT7__SD2_DATA7 0x4170b9
+ MX6SL_PAD_SD2_RST__SD2_RESET 0x4170b9
>;
};
@@ -188,6 +193,7 @@
MX6SL_PAD_SD2_DAT5__SD2_DATA5 0x4170f9
MX6SL_PAD_SD2_DAT6__SD2_DATA6 0x4170f9
MX6SL_PAD_SD2_DAT7__SD2_DATA7 0x4170f9
+ MX6SL_PAD_SD2_RST__SD2_RESET 0x4170f9
>;
};
--
1.9.1

14
bsp/buildroot/board/freescale/warpboard/post-image.sh Executable file
View File

@@ -0,0 +1,14 @@
#!/usr/bin/env bash
BOARD_DIR="$(dirname $0)"
GENIMAGE_CFG="${BOARD_DIR}/genimage.cfg"
GENIMAGE_TMP="${BUILD_DIR}/genimage.tmp"
rm -rf "${GENIMAGE_TMP}"
genimage \
--rootpath "${TARGET_DIR}" \
--tmppath "${GENIMAGE_TMP}" \
--inputpath "${BINARIES_DIR}" \
--outputpath "${BINARIES_DIR}" \
--config "${GENIMAGE_CFG}"