Update buidlroot to version 2016.08.1

bsp/buildroot/board/raspberrypi/genimage-raspberrypi0.cfg

@@ -0,0 +1,30 @@
+image boot.vfat {
+  vfat {
+    files = {
+      "bcm2708-rpi-b-plus.dtb",
+      "rpi-firmware/bootcode.bin",
+      "rpi-firmware/cmdline.txt",
+      "rpi-firmware/config.txt",
+      "rpi-firmware/fixup.dat",
+      "rpi-firmware/start.elf",
+      "kernel-marked/zImage"
+    }
+  }
+  size = 32M
+}
+
+image sdcard.img {
+  hdimage {
+  }
+
+  partition boot {
+    partition-type = 0xC
+    bootable = "true"
+    image = "boot.vfat"
+  }
+
+  partition rootfs {
+    partition-type = 0x83
+    image = "rootfs.ext4"
+  }
+}

bsp/buildroot/board/raspberrypi/genimage-raspberrypi3.cfg

@@ -0,0 +1,30 @@
+image boot.vfat {
+  vfat {
+    files = {
+      "bcm2710-rpi-3-b.dtb",
+      "rpi-firmware/bootcode.bin",
+      "rpi-firmware/cmdline.txt",
+      "rpi-firmware/config.txt",
+      "rpi-firmware/fixup.dat",
+      "rpi-firmware/start.elf",
+      "kernel-marked/zImage"
+    }
+  }
+  size = 32M
+}
+
+image sdcard.img {
+  hdimage {
+  }
+
+  partition boot {
+    partition-type = 0xC
+    bootable = "true"
+    image = "boot.vfat"
+  }
+
+  partition rootfs {
+    partition-type = 0x83
+    image = "rootfs.ext4"
+  }
+}

bsp/buildroot/board/raspberrypi/post-build.sh

@@ -0,0 +1,11 @@
+#!/bin/sh
+
+set -u
+set -e
+
+# Add a console on tty1
+if [ -e ${TARGET_DIR}/etc/inittab ]; then
+    grep -qE '^tty1::' ${TARGET_DIR}/etc/inittab || \
+	sed -i '/GENERIC_SERIAL/a\
+tty1::respawn:/sbin/getty -L  tty1 0 vt100 # HDMI console' ${TARGET_DIR}/etc/inittab
+fi

bsp/buildroot/board/raspberrypi/readme.txt

@@ -6,7 +6,8 @@ Intro
 These instructions apply to all models of the Raspberry Pi:
   - the original models A and B,
   - the "enhanced" models A+ and B+,
-  - the model B2 (aka Raspberry Pi 2).
+  - the model B2 (aka Raspberry Pi 2)
+  - the model B3 (aka Raspberry Pi 3).
 
 How to build it
 ===============
@@ -21,10 +22,14 @@ For models A, B, A+ or B+:
 
   $ make raspberrypi_defconfig
 
-And for model 2 B:
+For model 2 B:
 
   $ make raspberrypi2_defconfig
 
+For model 3 B:
+
+  $ make raspberrypi3_defconfig
+
 Build the rootfs
 ----------------
 
@@ -46,6 +51,7 @@ After building, you should obtain this tree:
     +-- bcm2708-rpi-b.dtb           [1]
     +-- bcm2708-rpi-b-plus.dtb      [1]
     +-- bcm2709-rpi-2-b.dtb         [1]
+    +-- bcm2710-rpi-3-b.dtb         [1]
     +-- boot.vfat
     +-- kernel-marked/zImage        [2]
     +-- rootfs.ext4
@@ -74,4 +80,6 @@ Copy the bootable "sdcard.img" onto an SD card with "dd":
   $ sudo dd if=output/images/sdcard.img of=/dev/sdX
 
 Insert the SDcard into your Raspberry Pi, and power it up. Your new system
-should come up now.
+should come up now and start two consoles: one on the serial port on
+the P1 header, one on the HDMI output where you can login using a USB
+keyboard.