update buildroot to 2017.02.11

bsp/buildroot-2017.02.11/board/freescale/p1010rdb/linux-4.1.config

@@ -0,0 +1,70 @@
+CONFIG_PPC_85xx=y
+CONFIG_PHYS_64BIT=y
+CONFIG_SYSVIPC=y
+CONFIG_NO_HZ=y
+CONFIG_HIGH_RES_TIMERS=y
+CONFIG_LOG_BUF_SHIFT=14
+CONFIG_EXPERT=y
+CONFIG_MODULES=y
+CONFIG_P1010_RDB=y
+CONFIG_HIGHMEM=y
+CONFIG_SWIOTLB=y
+CONFIG_FORCE_MAX_ZONEORDER=12
+CONFIG_PCI=y
+CONFIG_PCI_MSI=y
+CONFIG_RAPIDIO=y
+CONFIG_NET=y
+CONFIG_PACKET=y
+CONFIG_UNIX=y
+CONFIG_INET=y
+CONFIG_DEVTMPFS=y
+CONFIG_MTD=y
+CONFIG_MTD_CMDLINE_PARTS=y
+CONFIG_MTD_BLOCK=y
+CONFIG_FTL=y
+CONFIG_MTD_CFI=y
+CONFIG_MTD_CFI_INTELEXT=y
+CONFIG_MTD_CFI_AMDSTD=y
+CONFIG_MTD_PHYSMAP_OF=y
+CONFIG_MTD_NAND=y
+CONFIG_MTD_NAND_FSL_ELBC=y
+CONFIG_MTD_NAND_FSL_IFC=y
+CONFIG_BLK_DEV_SD=y
+CONFIG_CHR_DEV_SG=y
+CONFIG_ATA=y
+CONFIG_SATA_FSL=y
+CONFIG_NETDEVICES=y
+CONFIG_GIANFAR=y
+CONFIG_VITESSE_PHY=y
+CONFIG_FIXED_PHY=y
+CONFIG_SERIAL_8250=y
+CONFIG_SERIAL_8250_CONSOLE=y
+CONFIG_SERIAL_8250_NR_UARTS=2
+CONFIG_SERIAL_8250_RUNTIME_UARTS=2
+CONFIG_SERIAL_8250_MANY_PORTS=y
+CONFIG_SERIAL_8250_DETECT_IRQ=y
+CONFIG_SERIAL_8250_RSA=y
+CONFIG_NVRAM=y
+CONFIG_I2C=y
+CONFIG_I2C_CHARDEV=y
+CONFIG_I2C_MPC=y
+CONFIG_SPI=y
+CONFIG_SPI_FSL_SPI=y
+CONFIG_SPI_FSL_ESPI=y
+CONFIG_USB=y
+CONFIG_USB_EHCI_HCD=y
+CONFIG_USB_EHCI_FSL=y
+CONFIG_USB_STORAGE=y
+CONFIG_MMC=y
+CONFIG_MMC_SDHCI=y
+CONFIG_MMC_SDHCI_PLTFM=y
+CONFIG_MMC_SDHCI_OF_ESDHC=y
+CONFIG_RTC_CLASS=y
+CONFIG_RTC_DRV_CMOS=y
+CONFIG_DMADEVICES=y
+CONFIG_FSL_DMA=y
+CONFIG_EXT4_FS=y
+CONFIG_TMPFS=y
+CONFIG_JFFS2_FS=y
+CONFIG_SQUASHFS=y
+CONFIG_CRYPTO_DEV_FSL_CAAM=y

bsp/buildroot-2017.02.11/board/freescale/p1010rdb/readme.txt

@@ -0,0 +1,40 @@
+You'll need to program the files created by buildroot into the flash.
+The fast way is to tftp transfer the files via one of the network interfaces.
+
+Alternatively you can transfer the files via serial console with an Ymodem
+file transfer from your terminal program by using a "loady" command
+from the u-boot prompt instead of the "tftp ..." commands stated below.
+Beware that serial console file transfers are quite slow!
+
+1. Program the DTB to NOR flash
+
+    => tftp $loadaddr p1010rdb-pa.dtb
+    => erase 0xee000000 +$filesize
+    => cp.b $loadaddr 0xee000000 $filesize
+
+2. Program the kernel to NOR flash
+
+    => tftp $loadaddr uImage
+    => erase 0xee080000 +$filesize
+    => cp.b $loadaddr 0xee080000 $filesize
+
+3. Program the root filesystem to NOR flash
+
+    => tftp $loadaddr rootfs.jffs2
+    => erase 0xee800000 0xeff5ffff
+    => cp.b $loadaddr 0xee800000 $filesize
+
+4. Booting your new system
+
+    => setenv norboot 'setenv bootargs root=/dev/mtdblock2 rootfstype=jffs2 console=$consoledev,$baudrate;bootm 0xee080000 - 0xee000000'
+
+    If you want to set this boot option as default:
+
+    => setenv bootcmd 'run norboot'
+    => saveenv
+
+    ...or for a single boot:
+
+    => run norboot
+
+    You can login with user "root".