Bump buidlroot version to 2018.02.6

bsp/buildroot/board/lemaker/bananapro/boot.cmd

@@ -0,0 +1,5 @@
+setenv fdt_high ffffffff
+setenv bootargs console=ttyS0,115200 earlyprintk root=/dev/mmcblk0p2 rootwait
+fatload mmc 0 $kernel_addr_r zImage
+fatload mmc 0 $fdt_addr_r sun7i-a20-bananapro.dtb
+bootz $kernel_addr_r - $fdt_addr_r

bsp/buildroot/board/lemaker/bananapro/genimage.cfg

@@ -0,0 +1,37 @@
+# Minimal SD card image for the Banana Pro
+# Based in the Orange Pi genimage.cfg
+
+image boot.vfat {
+	vfat {
+		files = {
+			"zImage",
+			"sun7i-a20-bananapro.dtb",
+			"boot.scr"
+		}
+	}
+	size = 10M
+}
+
+image sdcard.img {
+	hdimage {
+	}
+
+	partition u-boot {
+		in-partition-table = "no"
+		image = "u-boot-sunxi-with-spl.bin"
+		offset = 8192
+		size = 1040384 # 1MB - 8192
+	}
+
+	partition boot {
+		partition-type = 0xC
+		bootable = "true"
+		image = "boot.vfat"
+	}
+
+	partition rootfs {
+		partition-type = 0x83
+		image = "rootfs.ext4"
+		size = 512M
+	}
+}

bsp/buildroot/board/lemaker/bananapro/linux-wifi.fragment

@@ -0,0 +1,23 @@
+# Networking support
+CONFIG_WIRELESS=y
+CONFIG_CFG80211=y
+CONFIG_CFG80211_WEXT=y
+
+# Network device support
+CONFIG_WLAN=y
+CONFIG_WLAN_VENDOR_BROADCOM=y
+CONFIG_BRCMFMAC=m
+# CONFIG_WLAN_VENDOR_ADMTEK is not set
+# CONFIG_WLAN_VENDOR_ATH is not set
+# CONFIG_WLAN_VENDOR_ATMEL is not set
+# CONFIG_WLAN_VENDOR_CISCO is not set
+# CONFIG_WLAN_VENDOR_INTEL is not set
+# CONFIG_WLAN_VENDOR_INTERSIL is not set
+# CONFIG_WLAN_VENDOR_MARVELL is not set
+# CONFIG_WLAN_VENDOR_MEDIATEK is not set
+# CONFIG_WLAN_VENDOR_RALINK is not set
+# CONFIG_WLAN_VENDOR_REALTEK is not set
+# CONFIG_WLAN_VENDOR_RSI is not set
+# CONFIG_WLAN_VENDOR_ST is not set
+# CONFIG_WLAN_VENDOR_TI is not set
+# CONFIG_WLAN_VENDOR_ZYDAS is not set

bsp/buildroot/board/lemaker/bananapro/post-build.sh

@@ -0,0 +1,12 @@
+#!/bin/sh
+
+# Remove all but the brcmfmac43362 firmware files
+find $TARGET_DIR/lib/firmware/brcm -type f -not -name "brcmfmac43362*" -delete
+
+BOARD_DIR="$(dirname $0)"
+MKIMAGE=$HOST_DIR/bin/mkimage
+BOOT_CMD=$BOARD_DIR/boot.cmd
+BOOT_CMD_H=$BINARIES_DIR/boot.scr
+
+# U-Boot script
+$MKIMAGE -C none -A arm -T script -d $BOOT_CMD $BOOT_CMD_H

bsp/buildroot/board/lemaker/bananapro/post-image.sh

@@ -0,0 +1,16 @@
+#!/bin/sh
+
+BOARD_DIR="$(dirname $0)"
+GENIMAGE_CFG="${BOARD_DIR}/genimage.cfg"
+GENIMAGE_TMP="${BUILD_DIR}/genimage.tmp"
+
+rm -rf "${GENIMAGE_TMP}"
+
+genimage                           \
+	--rootpath "${TARGET_DIR}"     \
+	--tmppath "${GENIMAGE_TMP}"    \
+	--inputpath "${BINARIES_DIR}"  \
+	--outputpath "${BINARIES_DIR}" \
+	--config "${GENIMAGE_CFG}"
+
+exit $?

bsp/buildroot/board/lemaker/bananapro/readme.txt

@@ -0,0 +1,62 @@
+Banana Pro
+
+Intro
+=====
+
+This default configuration will allow you to start experimenting with the
+Buildroot environment for the Banana Pro. With the current configuration
+it will bring-up the board, and allow access through the serial console.
+
+How to build it
+===============
+
+Configure Buildroot:
+
+  $ make bananapro_defconfig
+
+Compile everything and build the SD card image:
+
+  $ make
+
+How to write the SD card
+========================
+
+Once the build process is finished you will have an image called "sdcard.img"
+in the output/images/ directory.
+
+Copy the bootable "sdcard.img" onto an SD card with "dd":
+
+  $ dd if=output/images/sdcard.img of=/dev/sdX
+
+Notes:
+  - replace 'sdX' with the actual device with your micro SD card
+  - you may need to be root to do that (use 'sudo')
+
+Insert the micro SD card in your Banana Pro and power it up. The console
+is on the debug TTL UART, 115200 8N1.
+
+Ethernet
+==========
+
+  # udhcpc -i eth0
+
+Wifi
+==========
+
+  # wpa_passphrase YOUR_SSID >> /etc/wpa_supplicant.conf
+  (enter the wifi password and press enter)
+  # wpa_supplicant -i wlan0 -c /etc/wpa_supplicant.conf -B
+  # udhcpc -i wlan0
+
+Note:
+  - replace 'YOUR_SSID' with the actual SSID from your access point
+
+Audio
+==========
+
+Connect a headphone to the 3.5mm jack (TRRS). Note, that the Banana Pro
+has an on-board microphone, too.
+
+  # amixer cset name='Power Amplifier DAC Playback Switch' on
+  # amixer cset name='Power Amplifier Mute Switch' on
+  # amixer cset name='Power Amplifier Volume' 42

bsp/buildroot/board/lemaker/bananapro/rootfs_overlay/lib/firmware/brcm/brcmfmac43362-sdio.txt

@@ -0,0 +1,56 @@
+#AP6210_NVRAM_V1.2_03192013
+manfid=0x2d0
+prodid=0x492
+vendid=0x14e4
+devid=0x4343
+boardtype=0x0598
+
+# Board Revision is P307, same nvram file can be used for P304, P305, P306 and P307 as the tssi pa params used are same
+#Please force the automatic RX PER data to the respective board directory if not using P307 board, for e.g. for P305 boards force the data into the following directory /projects/BCM43362/a1_labdata/boardtests/results/sdg_rev0305
+boardrev=0x1307
+boardnum=777
+xtalfreq=26000
+boardflags=0x80201
+boardflags2=0x80
+sromrev=3
+wl0id=0x431b
+macaddr=00:90:4c:07:71:12
+aa2g=1
+ag0=2
+maxp2ga0=74
+cck2gpo=0x2222
+ofdm2gpo=0x44444444
+mcs2gpo0=0x6666
+mcs2gpo1=0x6666
+pa0maxpwr=56
+
+#P207 PA params
+#pa0b0=5447
+#pa0b1=-658
+#pa0b2=-175
+
+#Same PA params for P304,P305, P306, P307
+
+pa0b0=5447
+pa0b1=-607
+pa0b2=-160
+pa0itssit=62
+pa1itssit=62
+
+
+cckPwrOffset=5
+ccode=0
+rssismf2g=0xa
+rssismc2g=0x3
+rssisav2g=0x7
+triso2g=0
+noise_cal_enable_2g=0
+noise_cal_po_2g=0
+swctrlmap_2g=0x04040404,0x02020202,0x02020202,0x010101,0x1ff
+temp_add=29767
+temp_mult=425
+
+btc_flags=0x6
+btc_params0=5000
+btc_params1=1000
+btc_params6=63